On the characteristics of natural hydraulic dampers: An image-based approach to study the fluid flow behaviour inside the human meniscal tissue.

The meniscal tissue is a layered material with varying properties influenced by collagen content and arrangement. Understanding the relationship between structure and properties is crucial for disease management, treatment development, and biomaterial design. The internal layer of the meniscus is softer and more deformable than the outer layers, thanks to interconnected collagen channels that guide fluid flow. To investigate these relationships, we propose an integrated approach that combines Computational Fluid Dynamics (CFD) with Image Analysis (CFD-IA). We analyze fluid flow in the internal architecture of the human meniscus across a range of inlet velocities (0.1 mm/s to 1.6 m/s) using high-resolution 3D micro-computed tomography scans. Statistical correlations are observed between architectural parameters (tortuosity, connectivity, porosity, pore size) and fluid flow parameters (Re number distribution, permeability). Some channels exhibit Re values of 1400 at an inlet velocity of 1.6 m/s, and a transition from Darcy's regime to a non-Darcian regime occurs around an inlet velocity of 0.02 m/s. Location-dependent permeability ranges from 20-32 Darcy. Regression modelling reveals a strong correlation between fluid velocity and tortuosity at high inlet velocities, as well as with channel diameter at low inlet velocities. At higher inlet velocities, flow paths deviate more from the preferential direction, resulting in a decrease in the concentration parameter by an average of 0.4. This research provides valuable insights into the fluid flow behaviour within the meniscus and its structural influences. 3D models and image stack are available to download at https://doi.org/10.5281/zenodo.10401592. STATEMENT OF SIGNIFICANCE: The meniscus is a highly porous soft tissue with remarkable properties of load transfer and energy absorption. We give insight on the mechanism of energy absorption from high resolution uCT scans, never presented before, and a new method which combine CFD and image. The structure is similar to a sandwich structure with a stiff outside layer and a soft internal layer made of collagen channels oriented in a preferential direction guiding the fluid flow, enabling it to accommodate deformation and dissipate energy, making it a potentially optimized damping system. We investigate architectural/ fluid flow parameters- fluid regimes relationship, which is of interest of the readers working on designing suitable biomimetic systems that can be adopted for replacement.

Polybutylene Succinate Processing and Evaluation as a Micro Fibrous Graft for Tissue Engineering Applications.

A microfibrous tubular scaffold has been designed and fabricated by electrospinning using poly (1,4-butylene succinate) as biocompatible and biodegradable material. The scaffold morphology was optimized as a small diameter and micro-porous conduit, able to foster cell integration, adhesion, and growth while avoiding cell infiltration through the graft's wall. Scaffold morphology and mechanical properties were explored and compared to those of native conduits. Scaffolds were then seeded with adult normal human dermal fibroblasts to evaluate cytocompatibility in vitro. Haemolytic effect was evaluated upon incubation with diluted whole blood. The scaffold showed no delamination, and mechanical properties were in the physiological range for tubular conduits: elastic modulus (17.5 ± 1.6 MPa), ultimate tensile stress (3.95 ± 0.17 MPa), strain to failure (57 ± 4.5%) and suture retention force (2.65 ± 0.32 N). The shown degradation profile allows the graft to provide initial mechanical support and functionality while being colonized and then replaced by the host cells. This combination of features might represent a step toward future research on PBS as a biomaterial to produce scaffolds that provide structure and function over time and support host cell remodelling.

Gastro-Resistant Microparticles Produced by Spray-Drying as Controlled Release Systems for Liposoluble Vitamins.

In the present study, gastro-resistant microparticles (MPs) were produced using the spray-drying technique as controlled-release systems for some model liposoluble vitamins, including retinyl-palmitate, retinyl-acetate, ß-carotene, cholecalciferol and α-tocopherol. The gastroprotective action of three different gastro-resistant excipients, the anionic methacrylic copolymer (Eudraguard®® Biotic, E1207), the cellulose acetate phthalate (CAP) and whey proteins (WPs), was compared. The latter was used to produce a novel delivery system manufactured with only food-derived components, such as milk, and showed several improvements over the two synthetic gastro-resistant agents. Scanning electron microscopy (SEM) images showed a quite homogeneous spherical shape of all microparticle batches, with an average diameter between 7 and 15 µm. FTIR analysis was used to evaluate the effective incorporation of vitamins within the microparticles and the absence of any degradation to the components of the formulation. The comparison graphs of differential scanning calorimetry (DSC) confirmed that the spray drying technique generates a solid in which the physical interactions between the excipients and the vitamins are very strong. Release studies showed a prominent pH-controlled release and partially a delayed-release profile. Ex vivo permeation studies of retinyl palmitate, retinyl acetate and α-tocopherol revealed greater transmucosal permeation capacity for microparticles produced with the WPs and milk.

Identification of microplastics using 4-dimethylamino-4'-nitrostilbene solvatochromic fluorescence.

In this work, we introduce the use of 4-dimethylamino-4'-nitrostilbene (DANS) fluorescent dye for applications in the detection and analysis of microplastics, an impendent source of pollution made of synthetic organic polymers with a size varying from less than 5 mm to nanometer scale. The use of this dye revealed itself as a versatile, fast and sensitive tool for readily discriminate microplastics in water environment. The experimental evidences herein presented demonstrate that DANS efficiently absorbs into a variety of polymers constituting microplastics, and its solvatochromic properties lead to a positive shift of the fluorescence emission spectrum according to the polarity of the polymers. Therefore, under UV illumination, microplastics glow a specific emission spectrum from blue to red that allows for a straightforward polymer identification. In addition, we show that DANS staining gives access to different detection and analysis strategies based on fluorescence microscopy, from simple epifluorescence fragments visualization, to confocal microscopy and phasor approach for plastic components quantification.